|
|
Flexible Waveguides
MEGA INDUSTRIES provides flexible waveguides in sizes WR90 through WR2300. Full height and reduced height configurations are available to meet our customer’s requirements. Custom sizes through WR4750 are also available upon special request.
Flexible Waveguides are manufactured from aluminum or copper alloys with various flange configurations to meet EIA and Military specifications. The flexible waveguide may be plated in accordance with customer requirements. Typical finishes are copper, silver, gold and copper or aluminum iridite. Exterior protective coatings include black oxide, zinc, and tin plating or molded neoprene, polyurethane and various paint and enamels.
MEGA INDUSTRIES provides full design services for factory formed bends and twists to assure accuracy and electrical performance. A ten percent (10%) operating frequency bandwidth is requested to provide optimum VSWR results
MEGA INDUSTRIES recommends utilization of flexible waveguide sections to correct misalignment conditions between two interfacing subsystems and where nominal expansion and contraction in a microwave feed must be absorbed.
These flexible waveguide sections are supplied with flush type flanges that interface with EIA standards.
Semi-flexible Waveguides
Semi-flexible waveguides manufactured by Mega Industries are available in various materials depending on the waveguide size. The typical materials used are: Aluminum, Copper, Brass and Phosphor Bronze.
Our process of brazing the seam off center assures excellent electrical performance for your high power applications. By brazing, and not joining by epoxy, you are assured a good long life joint not prone to splitting or leaking.
In addition Mega Industries offers a welded seam semi-flexible waveguide in sizes WR187, WR229, WR284 in phosphor bronze, thus affording you increased flexibility over units manufactured in aluminum.
Our waveguides meet or exceed the requirements of MIL-DTL-287-F and are available with finishes such as copper, silver, gold and copper and aluminum iridite. Exterior protective coatings include black oxide, zinc, and tin plating or molded neoprene, polyurethane, and various paints and enamels.
Mega Industries provides full design services for factory formed bends and twists to assure accuracy and electrical performance.
Mega Industries provides flexible waveguides in sizes WR90 through WR2300. Full height and reduced height configurations are available to meet your requirements. Custom sizes through WR6200 are also available on special request.
Seamless Semi-Flexible Waveguide
 Mega Industries WR90 seamless semi-flexible waveguide is manufactured using only the highest quality phosphor bronze tube. This offers you the best combination of flexibility and structural integrity ensuring you of unsurpassed performance for your system.
This waveguide is constructed from thin wall tubing convoluted at our factory using our proprietary convoluting method assuring you of exacting specifications. Because of its seamless construction, the waveguide offers leak free construction both for RF and pressurization.
 Semi-Flexible Waveguides
Product Data Sheet
Compressed Convolution Semi-Flexible Waveguides
Compressed Convolution Semi-flexible waveguides manufactured by Mega Industries offers you one more option for your tough connection and low force requirements. This unique waveguide offers the same excellent electrical performance you have come to expect and demand from Mega Industries, while giving you that extra flexibility that you need in those tight connections that your layout may demand.
Our convoluting process allows for increased movement in both the E and H plane while requiring less force for compression and expansion. Because of the unique compression technique, this waveguide will offer greater expansion capabilities, however slightly less compression than our standard semi-flexible waveguide. This enhanced capability yields a softer move forgiving section that can prove extremely valuable in areas that would normally make for a difficult connection.
Our process of brazing the seam off center assures excellent electrical performance for your high power applications. By brazing, and not joining by epoxy, you are assured a good long life joint not prone to splitting or leaking.
Our waveguides meet or exceed the requirements of MIL-DTL-287-F and are available with finishes such as copper, silver, gold, and copper/aluminum iridite. Exterior protective coatings include black oxide, zinc, and tin plating or molded neoprene, Polyurethane and various paints and enamels.
Mega Industries provides full design services for factory formed bends and twists to assure accuracy and electrical performance.
Mega Industries provides compressed convolution flexible waveguides in sizes WR650 through WR2300. Full height and reduced height configurations are available to meet your requirements. Custom sizes are also available on special request.
Compressed Convolution Semi-Flexible Waveguides
Product Data Sheet
|
|
